Sames Reset

Found message error on printer Lexmark Optra C710, Optra 720 and Optra 750. Here the maintenance Message Reset Methods for Lexmark Optra C710, 720, 750 printers

Optra C710

1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test the display will read CONFIG MENU
2. Press the MENU button right or left until RESET FUSER COUNT appears
3. Press the SELECT button to reset the count
   

Optra C720

1. Enter the Diagnostic Menu for all resets by pressing the GO and RETURN buttons and turn the printer on
2. Continue holding until PERFORMING SELF TEST is displayed
3. Select RESET COUNTERS from the Diagnostic Menu
4. Select the individual counter for reset and press the SELECT button
   

Optra C750

1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test, the display will read CONFIG MENU
2. Select individual reset for fuser or ITU kit

Canon Pixma MX300 is one of the Inkjet multifuction (Print, Scan, Copy, Fax) printer from Canon. Like general case of printer, after filled by ink usually ink level not full. At some cases of printer, after ink level empty, printer cannot be used to print.

Here the Solution to reset the ink level for Canon Pixma MX300, follow this steps to reset the ink level in your canon MX300.

1. Switch off the Canon MX300 and disconnect the power cable.
2. While press and hold the power button, Connect the power cable to electric socket.
3. While pressing the power button, press the “Cancel/Stop” button (red button).
4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says “idle”.
5. Press “>” (next button) once “Shipping Mode 3″ then Press the “OK” button. Press “OK” again for “without cleaning”.
6. A test page will print.
7. Open the cover, like you are about to change the cartridges.
8. Disconnect the power cable again without switch off the printer.
9. Take out the both cartridges.
10. Close the cover.
11. Connect the power cable and turn on the printer.
12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.

Here is how to reset the waste counter for the Epson R200, R210, R300 and R310 printers.

• Press and hold “Stop”, “Maintenance”, and “Power” buttons for about 10 seconds. A message will come on the screen saying counter is reset and to turn the printer off. The R200 and others don’t have a screen so just wait until the 10 seconds is up.
• Turn the printer off, unplug the power cord. Wait about 1 minute and power the printer back up. The counter will be reset. That’s all there is to the reset procedure.
  

Is the waste pad full ?

If the waste pad is actually full and ink is about to overflow, then you need to install a waste container. You can see the waste pad by opening the access panel on the back of the printer.

Changing the waste pad requires almost complete disassembly of the printer, it is a big job. There is an easier way.

Open the access panel on the rear of the printer (remove screw) and look inside carefullly with a flashlight. You will see a tube (down and to your left) coming from the cleaning pump and it will have an open end on it. This is the tube that delivers ink to the waste pad.

Use a piece of coathanger wire or equivalent, and fish out this piece of tube. Bring it to the outside of the printer, thru the access panel.

Find yourself a suitable container (Tupperware or a plastic cup or jar) that is not too tall. Put the tube into this container and secure the tube and container so they won’t come apart or lose connection if the printer is moved.

If you wish you can make a hole or notch in the access panel cover so it can be replaced.

Now the ink will go into this container and not into the waste pad inside the printer. If it gets full, dump it.

Note: This information and a couple of photos are also available on Steve’s Digicam Forum (http://stevesforums.com/forums). Goto Printers-Photo Inkjet-Epson R200-210 & R300-310 Mod

Download Software Resetter for Epson R300-310

Manual Reset Procedure for Printers Epson 2200

1. Turn off the printer power and unplug the power cord from the wall. Disconnect the computer interface cable at the back of the printer.
2. After one minute reattach the power plug to the wall, but don’t reattach the computer cable.
3. Hold down the ROLL and the PAPER ADVANCE buttons simultaneously.
4. Turn the printer on. after 2 blinks, all the ink lights come on, then release the buttons being held down.
5. Press and hold the ROLL button for 10 seconds.
6. Release the ROLL button and the printer will initialize, which resets the Waste Ink Pad Counter.
7. Once initialization is complete, turn the printer power off.
8. Reconnect the interface cable.
9. Turn the printer on and print a document.

Cold resetting a printer resets the printer to factory defaults. Please note: Any settings you make at the printers control panel will be reset to factory defaults, including the IP address if you have a JetDirect card installed. Remove the JetDirect card while you cold reset the printer if you don't want to erase the JetDirect card's settings.

You can also reset the NVRAM. Resetting the NVRAM will clear the page count and reset the service mode settings to factory defaults. On printers with a display panel you need to enter service mode to manually change the information stored in NVRAM. On printers that don't have a display panel, such as a 5P, 6P, 2100, 2200 there is a different procedure outlined below.

"Older" printers with a display panel. (e.g. 4000, 4100, 5si, 8000, etc.)

Cold resetting the printer is simply a matter of turning the power off, holding down the GO or Online button while turning the printer on.

Resetting NVRAM settings must be done manually through service mode. See entering service mode.

"Newer" printers with a display panel. (e.g. 2300, 2400, 4200, 4250/4350, 4300, etc.)

Turn the printer off and then on. When the printer begins its memory count, press and hold down the Checkmark button until all the main LED signal lights illuminate and stay illuminated. Then release the Checkmark button, and use the Up/Down arrow keys to find the Cold Reset option, then press the Checkmark button again to choose that option.

Printers with no display panel.

HP 1100, 1200 - While the printer is on, press and hold the Go button for 5 seconds. This will reset the printer. To reset the NVRAM. Turn the printer off. Press and hold the Go button for 20 seconds while powering on the printer.

HP 2100 - To perform a cold reset, turn the printer power off, then press and hold the JOB CANCEL button. Turn the printer power back on and after all the LEDs come on release the JOB CANCEL button. A cold reset changes most system parameters in NVRAM to the factory defaults. The JOB CANCEL button must be released within 20 seconds after all of the LEDs come on; otherwise, an NVRAM initialization is performed instead of a cold reset.

HP 2200 Cold reset :

1. Turn the printer power off.
2. Press and hold GO.
3. Turn the printer power back on and continue to hold GO until the Attention light turns on.
4. Release GO.
5. The device lights will begin cycling from front to rear. The cold-reset process will run until completion and the device will go to the ready state.
   

NVRAM Reset :

1. Turn the printer power off.
2. Press and hold GO.
3. Turn the printer power back on and continue to hold GO until the Attention, Ready, and Go lights turn on.
4. Release GO.
5. The device lights will begin cycling from font to rear. The NVRAM initialization will run until completion and the device will go to the ready state.
   

HP 5P & 6P Cold reset :

• Turn the power off and hold the reset button (button closest to the back of the printer) for LESS than 20 seconds while turning the printer on.

Reset the NVRAM :

• Turn the power off and hold the reset button for MORE than 20 seconds while turning the printer on..

haii guys... this is my blog, i dedicated for you that need help printer trouble shooting